National Aeronautics and Space Administration Wiki
Register
Advertisement

Question book-new

The factual accuracy of this article may be compromised due to out-of-date information

Template:Infobox rocket stage

The Space Shuttle Solid Rocket Boosters (SRBs) were the first solid fuel motors to be used for primary propulsion on a vehicle used for human spaceflight[1] and provided the majority of the Space Shuttle's thrust during the first two minutes of flight. After burnout, they were jettisoned and parachuted into the Atlantic Ocean where they were recovered, examined, refurbished, and reused.

The SRBs were the most powerful rocket motors ever flown.[2] Each provided a maximum Template:Convert/sround kN (3,100,000 lbf) thrust, roughly double the most powerful single-combustion chamber liquid-propellant rocket engine ever flown, the Rocketdyne F-1. With a combined mass of about 1,180,000 kg (Template:Convert/round lb), they comprised over half the mass of the Shuttle stack at liftoff. The motor segments of the SRBs were manufactured by Thiokol of Brigham City, Utah, which was later purchased by ATK. The prime contractor for most other components of the SRBs, as well as for the integration of all the components and retrieval of the spent SRBs, was USBI, a subsidiary of Pratt and Whitney. This contract was subsequently transitioned to United Space Alliance, a limited liability company joint venture of Boeing and Lockheed Martin.

Out of 270 SRBs launched over the Shuttle program, all but four were recovered – those from STS-51-L (last Challenger mission) and STS-4.[3] Over 5,000 parts were refurbished for reuse after each flight. The final set of SRBs that launched STS-135 included parts that flew on 59 previous missions, including STS-1.[4] Recovery also allowed post-flight examination of the boosters,[5] identification of anomalies, and incremental design improvements.[6]

Overview[]

STS-1 The Shuttle's Solid Rocket Boosters break away from Columbia's External Tank

Solid Rocket Booster (SRB) separation

The two reusable SRBs provided the main thrust to lift the shuttle off the launch pad and up to an altitude of about 150,000 ft (Template:Convert/round mi; Template:Convert/round km). While on the pad, the two SRBs carried the entire weight of the external tank and orbiter and transmitted the weight load through their structure to the mobile launch platform. Each booster had a liftoff thrust of approximately 2,800,000 pounds-force (Template:Convert/round MN) at sea level, increasing shortly after liftoff to about 3,100,000 lbf (Template:Convert/round MN). They were ignited after the three Space Shuttle Main Engines' thrust level was verified. Seventy-five seconds after SRB separation, SRB apogee occurred at an altitude of approximately 220,000 ft (Template:Convert/round mi; Template:Convert/round km); parachutes are then deployed and impact occurred in the ocean approximately 122 nautical miles (Template:Convert/round km) downrange, after which the two SRBs are recovered.

The SRBs were the largest solid-propellant motors ever flown and the first of such large rockets designed for reuse. Each is 149.16 ft (Template:Convert/round m) long and 12.17 ft (Template:Convert/round m) in diameter.

Each SRB weighed approximately 1,300,000 lb (Template:Convert/round kg) at launch. The two SRBs constituted about 69% of the total lift-off mass. The propellant for each solid rocket motor weighed approximately 1,100,000 lb (Template:Convert/round kg). The inert weight of each SRB was approximately 200,000 pounds (Template:Convert/round kg).

Primary elements of each booster were the motor (including case, propellant, igniter and nozzle), structure, separation systems, operational flight instrumentation, recovery avionics, pyrotechnics, deceleration system, thrust vector control system, and range safety destruct system.

While the terms "solid rocket motor" and "solid rocket booster" are often used interchangeably, in technical use they have specific meanings. The term "solid rocket motor" applied to the propellant, case, igniter and nozzle. "Solid rocket booster" applied to the entire rocket assembly, which included the rocket motor as well as the recovery parachutes, electronic instrumentation, separation rockets, range safety destruct system, and thrust vector control.

Each booster was attached to the external tank at the SRB's aft frame by two lateral sway braces and a diagonal attachment. The forward end of each SRB was attached to the external tank at the forward end of the SRB's forward skirt. On the launch pad, each booster also was attached to the mobile launcher platform at the aft skirt by four frangible nuts that were severed at lift-off.

The boosters were composed of seven individually manufactured steel segments. These were assembled in pairs by the manufacturer, and then shipped to Kennedy Space Center by rail for final assembly. The segments were fixed together using circumferential tang, clevis, and clevis pin fastening, and sealed with three O-rings (two prior to the Challenger Disaster in 1986) and heat-resistant putty.

Components[]

Space Shuttle SRB diagram

SRB Diagram

Hold-down posts[]

Each solid rocket booster had four hold-down posts that fit into corresponding support posts on the mobile launcher platform. Hold-down bolts held the SRB and launcher platform posts together. Each bolt had a nut at each end, the top one being a frangible nut. The top nut contained two NASA standard detonators (NSDs), which were ignited at solid rocket motor ignition commands.

When the two NSDs were ignited at each hold down, the hold-down bolt traveled downward because of the release of tension in the bolt (pretensioned before launch), NSD gas pressure and gravity. The bolt was stopped by the stud deceleration stand, which contained sand. The SRB bolt was 28 in (Template:Convert/round mm) long and 3.5 in (Template:Convert/round mm) in diameter. The frangible nut was captured in a blast container.

The solid rocket motor ignition commands were issued by the orbiter's computers through the master events controllers to the hold-down pyrotechnic initiator controllers (PICs) on the mobile launcher platform. They provided the ignition to the hold-down NSDs. The launch processing system monitored the SRB hold-down PICs for low voltage during the last 16 seconds before launch. PIC low voltage would initiate a launch hold.

Electrical power distribution[]

Electrical power distribution in each SRB consisted of orbiter-supplied main DC bus power to each SRB via SRB buses labeled A, B and C. Orbiter main DC buses A, B and C supplied main DC bus power to corresponding SRB buses A, B and C. In addition, orbiter main DC bus C supplied backup power to SRB buses A and B, and orbiter bus B supplied backup power to SRB bus C. This electrical power distribution arrangement allowed all SRB buses to remain powered in the event one orbiter main bus failed.

The nominal operating voltage was 28±4 volts DC.

Hydraulic power units[]

There were two self-contained, independent Hydraulic Power Units (HPUs) on each SRB. Each HPU consisted of an auxiliary power unit (APU), fuel supply module, hydraulic pump, hydraulic reservoir and hydraulic fluid manifold assembly. The APUs were fueled by hydrazine and generated mechanical shaft power to drive a hydraulic pump that produced hydraulic pressure for the SRB hydraulic system. The two separate HPUs and two hydraulic systems were located on the aft end of each SRB between the SRB nozzle and aft skirt. The HPU components were mounted on the aft skirt between the rock and tilt actuators. The two systems operated from T minus 28 seconds until SRB separation from the orbiter and external tank. The two independent hydraulic systems were connected to the rock and tilt servoactuators.

The HPU controller electronics were located in the SRB aft integrated electronic assemblies on the aft external tank attach rings.

The HPUs and their fuel systems were isolated from each other. Each fuel supply module (tank) contained 22 lb (Template:Convert/round kg) of hydrazine. The fuel tank was pressurized with gaseous nitrogen at 400 psi (Template:Convert/round MPa), which provided the force to expel (positive expulsion) the fuel from the tank to the fuel distribution line, maintaining a positive fuel supply to the APU throughout its operation.

In the APU, a fuel pump boosted the hydrazine pressure and feeds it to a gas generator. The gas generator catalytically decomposed the hydrazine into hot, high-pressure gas; a two-stage turbine converted this into mechanical power, driving a gearbox. The waste gas, now cooler and at low pressure, was passed back over the gas generator housing to cool it before being dumped overboard. The gearbox drove the fuel pump, its own lubrication pump, and the HPU hydraulic pump. As described so far, the system could not self-start, since the fuel pump was driven by the turbine it supplied fuel to. Accordingly, a bypass line went around the pump and fed the gas generator using the nitrogen tank pressure until the APU speed was such that the fuel pump outlet pressure exceeded that of the bypass line, at which point all the fuel was supplied to the fuel pump.

When the APU speed reached 100%, the APU primary control valve closed, and the APU speed was controlled by the APU controller electronics. If the primary control valve logic failed to the open state, the secondary control valve assumed control of the APU at 112% speed.

Each HPU on an SRB was connected to both servoactuators on that SRB. One HPU served as the primary hydraulic source for the servoactuator, and the other HPU served as the secondary hydraulics for the servoactuator. Each servoactuator had a switching valve that allowed the secondary hydraulics to power the actuator if the primary hydraulic pressure dropped below 2,050 psi (Template:Convert/round MPa). A switch contact on the switching valve closed when the valve was in the secondary position. When the valve was closed, a signal was sent to the APU controller, that inhibited the 100% APU speed control logic and enabled the 112% APU speed control logic. The 100-percent APU speed enabled one APU/HPU to supply sufficient operating hydraulic pressure to both servoactuators of that SRB.

The APU 100-percent speed corresponded to 72,000 rpm, 110% to 79,200 rpm, and 112% to 80,640 rpm.

The hydraulic pump speed was 3,600 rpm and supplied hydraulic pressure of Template:Convert/±/AonSoff (Template:Convert/±/AonSoff). A high pressure relief valve provided overpressure protection to the hydraulic system and relieved at 3,750 psi (Template:Convert/round MPa).

The APUs/HPUs and hydraulic systems were reusable for 20 missions.

Thrust vector control[]

Each SRB had two hydraulic gimbal servoactuators, to move the nozzle up/down and side-to-side. This provided thrust vectoring to help control the vehicle in all three axes (roll, pitch, and yaw).

The ascent thrust vector control portion of the flight control system directed the thrust of the three shuttle main engines and the two SRB nozzles to control shuttle attitude and trajectory during lift-off and ascent. Commands from the guidance system were transmitted to the ATVC (Ascent Thrust Vector Control) drivers, which transmitted signals proportional to the commands to each servoactuator of the main engines and SRBs. Four independent flight control system channels and four ATVC channels controlled six main engine and four SRB ATVC drivers, with each driver controlling one hydraulic port on each main and SRB servoactuator.

Each SRB servoactuator consisted of four independent, two-stage servovalves that received signals from the drivers. Each servovalve controlled one power spool in each actuator, which positioned an actuator ram and the nozzle to control the direction of thrust.

The four servovalves in each actuator provided a "force-summed majority voting" arrangement to position the power spool. With four identical commands to the four servovalves, the actuator force-sum action prevented a single erroneous command from affecting power ram motion. If the erroneous command persisted for more than a predetermined time, differential pressure sensing activated a selector valve to isolate and remove the defective servovalve hydraulic pressure, permitting the remaining channels and servovalves to control the actuator ram spool.

Failure monitors were provided for each channel to indicate which channel had been bypassed. An isolation valve on each channel provided the capability of resetting a failed or bypassed channel.

Each actuator ram was equipped with transducers for position feedback to the thrust vector control system. Within each servoactuator ram was a splashdown load relief assembly to cushion the nozzle at water splashdown and prevent damage to the nozzle flexible bearing.

Rate gyro assemblies[]

Each SRB contained three Rate gyro assemblies (RGAs), with each RGA containing one pitch and one yaw gyro. These provided an output proportional to angular rates about the pitch and yaw axes to the orbiter computers and guidance, navigation and control system during first-stage ascent flight in conjunction with the orbiter roll rate gyros until SRB separation. At SRB separation, a switchover was made from the SRB RGAs to the orbiter RGAs.

The SRB RGA rates passed through the orbiter flight aft multiplexers/demultiplexers to the orbiter GPCs. The RGA rates were then mid-value-selected in redundancy management to provide SRB pitch and yaw rates to the user software. The RGAs were designed for 20 missions.

Propellant[]

The rocket propellant mixture in each SRB motor consisted of ammonium perchlorate (oxidizer, 69.6% by weight), aluminium (fuel, 16%), iron oxide (a catalyst, 0.4%), a polymer (PBAN, serving as a binder that held the mixture together and acted as secondary fuel, 12.04%), and an epoxy curing agent (1.96%).[7][8] This propellant is commonly referred to as Ammonium Perchlorate Composite Propellant, or simply APCP. This mixture develops a specific impulse of Template:Convert/isp at sea level or Template:Convert/isp in a vacuum.

The main fuel, aluminum, was used because it has a reasonable specific energy density of about 31.0 MJ/kg, but a high volumetric energy density, and is difficult to ignite accidentally.

The propellant had an 11-point star-shaped perforation in the forward motor segment and a double-truncated-cone perforation in each of the aft segments and aft closure. This configuration provided high thrust at ignition and then reduced the thrust by approximately a third 50 seconds after lift-off to avoid overstressing the vehicle during maximum dynamic pressure (Max Q).[7]

Function[]

Srbthrust2

SRB Sea Level Thrust. Data from STS-107

Ignition[]

SRB ignition can occur only when a manual lock pin from each SRB safe and arm device has been removed. The ground crew removes the pin during prelaunch activities. At T minus five minutes, the SRB safe and arm device is rotated to the arm position. The solid rocket motor ignition commands are issued when the three Space Shuttle Main Engines (SSMEs) are at or above 90-percent rated thrust, no SSME fail and/or SRB ignition Pyrotechnic Initiator Controller (PIC) low voltage is indicated and there are no holds from the Launch Processing System (LPS).

The solid rocket motor ignition commands are sent by the orbiter computers through the Master Events Controllers (MECs) to the safe and arm device NASA standard detonators ("NSD"s) in each SRB. A PIC single-channel capacitor discharge device controls the firing of each pyrotechnic device. Three signals must be present simultaneously for the PIC to generate the pyro firing output. These signals — arm, fire 1 and fire 2 — originate in the orbiter general-purpose computers (GPCs) and are transmitted to the MECs. The MECs reformat them to 28 volt DC signals for the PICs. The arm signal charges the PIC capacitor to 40 volts DC (minimum of 20 volts DC).

The GPC launch sequence also controls certain critical main propulsion system valves and monitors the engine ready indications from the SSMEs. The MPS start commands are issued by the onboard computers at T minus 6.6 seconds (staggered start engine three, engine two, engine one all approximately within 0.25 of a second), and the sequence monitors the thrust buildup of each engine. All three SSMEs must reach the required 90% thrust within three seconds; otherwise, an orderly shutdown is commanded and safing functions are initiated.

Normal thrust buildup to the required 90% thrust level will result in the SSMEs being commanded to the lift off position at T minus three seconds as well as the fire 1 command being issued to arm the SRBs. At T minus three seconds, the vehicle base bending load modes are allowed to initialize (referred to as the "twang", movement of approximately 25.5 in (Template:Convert/round mm) measured at the tip of the external tank, with movement towards the external tank).

The fire 2 commands cause the redundant NSDs to fire through a thin barrier seal down a flame tunnel. This ignites a pyro booster charge, which is retained in the safe and arm device behind a perforated plate. The booster charge ignites the propellant in the igniter initiator; and combustion products of this propellant ignite the solid rocket motor initiator, which fires down the entire vertical length of the solid rocket motor igniting the solid rocket motor propellant along its entire surface area instantaneously.

At T minus zero, the two SRBs are ignited, under command of the four onboard computers; separation of the four explosive bolts on each SRB is initiated; the two T-0 umbilicals (one on each side of the spacecraft) are retracted; the onboard master timing unit, event timer and mission event timers are started; the three SSMEs are at 100%; and the ground launch sequence is terminated.

Separation[]

The SRBs are jettisoned from the space shuttle at high altitude, about 146,000 ft (Template:Convert/round km). SRB separation is initiated when the three solid rocket motor chamber pressure transducers are processed in the redundancy management middle value select and the head-end chamber pressure of both SRBs is less than or equal to 50 psi (Template:Convert/round kPa). A backup cue is the time elapsed from booster ignition.

The separation sequence is initiated, commanding the thrust vector control actuators to the null position and putting the main propulsion system into a second-stage configuration (0.8 second from sequence initialization), which ensures the thrust of each SRB is less than 100,000 lbf (Template:Convert/round kN). Orbiter yaw attitude is held for four seconds, and SRB thrust drops to less than 60,000 lbf (Template:Convert/round kN).

The SRBs separate from the external tank within 30 milliseconds of the ordnance firing command.

The forward attachment point consists of a ball (SRB) and socket (External Tank (ET)) held together by one bolt. The bolt contains one NSD pressure cartridge at each end. The forward attachment point also carries the range safety system cross-strap wiring connecting each SRB RSS and the ET RSS with each other.

The aft attachment points consist of three separate struts: upper, diagonal and lower. Each strut contains one bolt with an NSD pressure cartridge at each end. The upper strut also carries the umbilical interface between its SRB and the external tank and on to the orbiter.

There are four booster separation motors on each end of each SRB. The BSMs separate the SRBs from the external tank. The solid rocket motors in each cluster of four are ignited by firing redundant NSD pressure cartridges into redundant confined detonating fuse manifolds.

The separation commands issued from the orbiter by the SRB separation sequence initiate the redundant NSD pressure cartridge in each bolt and ignite the BSMs to effect a clean separation.

Range safety system[]

A range safety system (RSS) provides for destruction of a rocket or part of it with on-board explosives by remote command if the rocket is out of control, in order to limit the danger to people on the ground from crashing pieces, explosions, fire, poisonous substances, etc. The RSS was only activated once – during the Space Shuttle Challenger disaster (37 seconds after the breakup of the vehicle, when the SRBs were in uncontrolled flight).

The shuttle vehicle had two RSSs, one in each SRB. Both were capable of receiving two command messages (arm and fire) transmitted from the ground station. The RSS was used only when the shuttle vehicle violates a launch trajectory red line.

An RSS consists of two antenna couplers, command receivers/decoders, a dual distributor, a safe and arm device with two NASA standard detonators (NSD), two confined detonating fuse manifolds (CDF), seven CDF assemblies and one linear-shaped charge (LSC).

The antenna couplers provide the proper impedance for radio frequency and ground support equipment commands. The command receivers are tuned to RSS command frequencies and provide the input signal to the distributors when an RSS command is sent. The command decoders use a code plug to prevent any command signal other than the proper command signal from getting into the distributors. The distributors contain the logic to supply valid destruct commands to the RSS pyrotechnics.

The NSDs provide the spark to ignite the CDF, which in turn ignites the LSC for booster destruction. The safe and arm device provides mechanical isolation between the NSDs and the CDF before launch and during the SRB separation sequence.

The first message, called arm, allows the onboard logic to enable a destruct and illuminates a light on the flight deck display and control panel at the commander and pilot station. The second message transmitted is the fire command.

The SRB distributors in the SRBs are cross-strapped together. Thus, if one SRB received an arm or destruct signal, the signal would also be sent to the other SRB.

Electrical power from the RSS battery in each SRB is routed to RSS system A. The recovery battery in each SRB is used to power RSS system B as well as the recovery system in the SRB. The SRB RSS is powered down during the separation sequence, and the SRB recovery system is powered up. [9]

Descent and recovery[]

Srb splashdown

Splashdown of the right hand SRB from the launch of STS-124.

The SRBs are jettisoned from the shuttle system at 2 minutes and an altitude of about 146,000 feet (44 km). After continuing to rise to about 220,000 feet (67 km), the SRBs begin to fall back to earth and once back in the atmosphere are slowed by a parachute system to prevent damage on ocean impact. A command is sent from the orbiter to the SRB just before separation to apply battery power to the recovery logic network. A second, simultaneous command arms the three nose cap thrusters (for deploying the pilot and drogue parachute), the frustum ring detonator (for main parachute deployment), and the main parachute disconnect ordnance.

The recovery sequence begins with the operation of the high-altitude baroswitch, which triggers the pyrotechnic nose cap thrusters. This ejects the nose cap, which deploys the pilot parachute. Nose cap separation occurs at a nominal altitude of 15,704 ft (Template:Convert/round m), about 218 seconds after SRB separation. The 11.5 ft (Template:Convert/LoffAonSon) diameter conical ribbon pilot parachute provides the force to pull lanyards attached to cut knives, which cut the loop securing the drogue retention straps. This allows the pilot chute to pull the drogue pack from the SRB, causing the drogue suspension lines to deploy from their stored position. At full extension of the twelve 105 ft (Template:Convert/round m) suspension lines, the drogue deployment bag is stripped away from the canopy, and the 54 ft (Template:Convert/LoffAonSon) diameter conical ribbon drogue parachute inflates to its initial reefed condition. The drogue disreefs twice after specified time delays (using redundant 7 and 12-second reefing line cutters), and it reorients/stabilizes the SRB for main chute deployment. The drogue parachute has a design load of approximately 315,000 lb (Template:Convert/round kg) and weighs approximately 1,200 lb (Template:Convert/round kg).

STS-116 rocket boosters (NASA KSC-06PD-2794)

The solid rocket boosters, jettisoned from the Space Shuttle Discovery following the launch of STS-116, floating in the Atlantic Ocean about 150 miles northeast of Cape Canaveral.

After the drogue chute has stabilized the SRB in a tail-first attitude, the frustum is separated from the forward skirt by a pyrotechnic charge triggered by the low-altitude baroswitch at a nominal altitude of 5,500 ft (Template:Convert/round m) about 243 seconds after SRB separation. The frustum is then pulled away from the SRB by the drogue chute. The main chute suspension lines are pulled out from deployment bags that remain in the frustum. At full extension of the lines, which are 203 ft (Template:Convert/round m) long, the three main chutes are pulled from their deployment bags and inflate to their first reefed condition. The frustum and drogue parachute continue on a separate trajectory to splashdown. After specified time delays (using redundant 10 and 17-second reefing line cutters), the main chute reefing lines are cut and the chutes inflate to their second reefed and full open configurations. The main chute cluster decelerates the SRB to terminal conditions. Each of the 136 ft (Template:Convert/round m) diameter, 20-degree conical ribbon parachutes have a design load of approximately 195,000 lb (Template:Convert/round kg) and each weighs approximately 2,180 lb (Template:Convert/round kg). These parachutes are the largest that have ever been used — both in deployed size and load weight. The RSRM nozzle extension is severed by a pyrotechnic charge about 20 seconds after frustum separation.

Water impact occurs about 279 seconds after SRB separation at a nominal velocity of 76 feet per second (Template:Convert/round m/s). The water impact range is approximately 130 nmi (Template:Convert/round km) off the eastern coast of Florida. Because the parachutes provide for a nozzle-first impact, air is trapped in the empty (burned out) motor casing, causing the booster to float with the forward end approximately 30 feet (Template:Convert/round m) out of the water.

Freedom Star with SRB

Solid rocket booster of the STS-131 mission being recovered and transported to Cape Canaveral by the Template:MV.

Formerly, the main chutes were released from the SRB at impact using a parachute release nut ordnance system (residual loads in the main chutes would deploy the parachute attach fittings with floats tethered to each fitting). The current design keeps the main chutes attached during water impact (initial impact and slapdown). Salt Water Activated Release (SWAR) devices are now incorporated into the main chute riser lines to simplify recovery efforts and reduce damage to the SRB.[10] The drogue deployment bag/pilot parachutes, drogue parachutes and frustums, each main chute, and the SRBs are buoyant and are recovered.

Specially fitted NASA recovery ships, the Template:MV and the Template:MV, recover the SRBs and descent/recovery hardware. Once the boosters are located, the Diver Operated Plug (DOP) is maneuvered by divers into place to plug the SRB nozzle and dewater the motor case. Dewatering, pumping air into and water out of the SRB, causes the SRB to change from a nose-up floating position to a horizontal attitude more suitable for towing. The retrieval vessels then tow the boosters and other objects recovered back to Kennedy Space Center.

Disastro dello Space Shuttle Challenger[]

Main article: Space Shuttle Challenger disaster
STS-51-L grey smoke on SRB

Camera captures grey smoke being emitted from the right-hand SRB on Space Shuttle Challenger before the start of STS-51-L.

La perdita di Space Shuttle Challenger ha avuto origine con un guasto al sistema di uno dei suoi SRB. La causa dell'incidente è stata trovata dalla Commissione Rogers come "un" progetto difettoso inaccettabilmente sensibile a una serie di fattori "delle articolazioni dell'SRB aggravano dal clima insolitamente freddo la mattina del volo. Commissione La commissione ha riscontrato che i grandi" O -ring "di gomma nelle articolazioni dell'SRB non erano efficaci a basse temperature come quelle della mattina dell'incidente del gennaio 1986 (☃☃☃☃). Un giunto compromesso dal freddo nell'SRB distrugge non è ottenuto al lancio e alla bene ha permesso ai gas caldi dall ' interno di quel booster di razzi di tariffa un buco nel serbatoio di combustibile esterno principale adiacente e anche di indebolire il montante inferiore che tiene l'SB al serbatoio esterno. La perdita nell'articolazione dell'SRB ha riscontrato un guasto catastrofico del montante inferiore e un parziale distacco dell'SRB, che ha portato una collisione tra l'SRB e il serbatoio esterno. Con un serbatoio esterno in via di disintegrazione e una forte spinta fuori asse dall'SRB destro, viaggiando con una velocità di Mach 1,92 a ☃☃, lo stack dello Space Shuttle è disintegrato e fu avvolto da una "bruciatura esplosiva" (cioè rapida deflagrazione) dei propellenti liquidi dal serbatoio esterno. SRB ha riscontrato un guasto catastrofico del montante inferiore e un parziale distacco dell'SRB, che ha portato una collisione tra l'SRB e il serbatoio esterno. Con un serbatoio esterno in via di disintegrazione e una forte spinta fuori asse dall'SRB destro, viaggiando con una velocità di Mach 1,92 a ☃☃, lo stack dello Space Shuttle è disintegrato e fu avvolto da una "bruciatura esplosiva" (cioè rapida deflagrazione) dei propellenti liquidi dal serbatoio esterno. SRB ha riscontrato un guasto catastrofico del montante inferiore e un parziale distacco dell'SRB, che ha portato una collisione tra l'SRB e il serbatoio esterno. Con un serbatoio esterno in via di disintegrazione e una forte spinta fuori asse dall'SRB destro, viaggiando con una velocità di Mach 1,92 a ☃☃, lo stack dello Space Shuttle è disintegrato e fu avvolto da una "bruciatura esplosiva" Con un serbatoio esterno in via di disintegrazione e una forte spinta fuori asse dall'SRB destro, viaggiando con una velocità di Mach 1,92 a ☃☃, lo stack dello Space Shuttle è disintegrato e fu avvolto da una "bruciatura esplosiva" (cioè rapida deflagrazione) dei propellenti liquidi dal serbatoio esterno. SRB ha riscontrato un guasto catastrofico del montante inferiore e un parziale distacco dell'SRB, che ha portato una collisione tra l'SRB e il serbatoio esterno. Con un serbatoio esterno in via di disintegrazione e una forte spinta fuori asse dall'SRB destro, viaggiando con una velocità di Mach 1,92 a ☃☃, lo stack dello Space Shuttle è disintegrato e fu avvolto da una "bruciatura esplosiva" Con un serbatoio esterno in via di disintegrazione e una forte spinta fuori asse dall'SRB destro, viaggiando con una velocità di Mach 1,92 a ☃☃, lo stack dello Space Shuttle è disintegrato e fu avvolto da una "bruciatura esplosiva" (cioè rapida deflagrazione) dei propellenti liquidi dal serbatoio esterno. SRB ha riscontrato un guasto catastrofico del montante inferiore e un parziale distacco dell'SRB, che ha portato una collisione tra l'SRB e il serbatoio esterno. Con un serbatoio esterno in via di disintegrazione e una forte spinta fuori asse dall'SRB destro, viaggiando con una velocità di Mach 1,92 a ☃☃, lo stack dello Space Shuttle è disintegrato e fu avvolto da una "bruciatura esplosiva" viaggiando con una velocità di Mach 1,92 a ☃☃, lo stack dello Space Shuttle è disintegrato e fu avvolto da una "bruciatura esplosiva" (cioè rapida deflagrazione) dei propellenti liquidi dal serbatoio esterno. SRB ha riscontrato un guasto catastrofico del montante inferiore e un parziale distacco dell'SRB, che ha portato una collisione tra l'SRB e il serbatoio esterno. Con un serbatoio esterno in via di disintegrazione e una forte spinta fuori asse dall'SRB destro, viaggiando con una velocità di Mach 1,92 a ☃☃, lo stack dello Space Shuttle è disintegrato e fu avvolto da una "bruciatura esplosiva" viaggiando con una velocità di Mach 1,92 a ☃☃, lo stack dello Space Shuttle è disintegrato e fu avvolto da una "bruciatura esplosiva" (cioè rapida deflagrazione) dei propellenti liquidi dal serbatoio esterno. SRB ha riscontrato un guasto catastrofico del montante inferiore e un parziale distacco dell'SRB, che ha portato una collisione tra l'SRB e il serbatoio esterno. Con un serbatoio esterno in via di disintegrazione e una forte spinta fuori asse dall'SRB destro, viaggiando con una velocità di Mach 1,92 a ☃☃, lo stack dello Space Shuttle è disintegrato e fu avvolto da una "bruciatura esplosiva" SRB ha riscontrato un guasto catastrofico del montante inferiore e un parziale distacco dell'SRB, che ha portato una collisione tra l'SRB e il serbatoio esterno. Con un serbatoio esterno in via di disintegrazione e una forte spinta fuori asse dall'SRB destro, viaggiando con una velocità di Mach 1,92 a ☃☃, lo stack dello Space Shuttle è disintegrato e fu avvolto da una "bruciatura esplosiva" SRB ha riscontrato un guasto catastrofico del montante inferiore e un parziale distacco dell'SRB, che ha portato una collisione tra l'SRB e il serbatoio esterno. Con un serbatoio esterno in via di disintegrazione e una forte spinta fuori asse dall'SRB destro, viaggiando con una velocità di Mach 1,92 a ☃☃, lo stack dello Space Shuttle è disintegrato e fu avvolto da una "bruciatura esplosiva"

During the subsequent downtime, detailed structural analyses were performed on critical structural elements of the SRB. Analyses were primarily focused in areas where anomalies had been noted during postflight inspection of recovered hardware.

One of the areas was the attachment ring where the SRBs are connected to the external tank. Areas of distress were noted in some of the fasteners where the ring attaches to the SRB motor case. This situation was attributed to the high loads encountered during water impact. To correct the situation and ensure higher strength margins during ascent, the attach ring was redesigned to encircle the motor case completely (360 degrees). Previously, the attachment ring formed a 'C' shape and encircled the motor case just 270 degrees.

Additionally, special structural tests were performed on the aft skirt. During this test program, an anomaly occurred in a critical weld between the hold-down post and skin of the skirt. A redesign was implemented to add reinforcement brackets and fittings in the aft ring of the skirt.

These two modifications added approximately 450 lb (Template:Convert/round kg) to the weight of each SRB. The result is called a "Redesigned Solid Rocket Motor" (RSRM).[11]

Construction[]

The prime contractor for the SRB motor segments was ATK Launch Systems' Wasatch Division based in Magna, Utah.

United Space Boosters Inc. (USBI), a division of Pratt and Whitney, under United Technologies, was the original SRB prime contractor for SRB assembly, checkout and refurbishment for all non-solid-rocket-motor components and for SRB integration. They were the longest running prime contractor for the Space Shuttle that was part of the original launch team. USBI was absorbed by United Space Alliance as the Solid Rocket Booster Element division in 1998 and the USBI division was disbanded at Pratt & Whitney the following year. At its peak, USBI had over 1500 personnel working on the Shuttle Boosters at KSC, FL and Huntsville, AL.

Many other companies supplied various components for the SRBs:[citation needed]

  • Parker-Abex Corp. of Kalamazoo, Michigan (hydraulic pumps)
  • Aerojet of Redmond, Washington (hydrazine gas generators)
  • Arde Inc. of Mahwah, New Jersey (hydrazine fuel supply modules)
  • Arkwin Industries Inc. of Westbury, New York (hydraulic reservoirs)
  • Aydin Vector Division of Newtown, Pennsylvania (integrated electronic assemblies)
  • Bendix Corp. of Teterboro, New Jersey (integrated electronic assemblies)
  • Consolidated Controls Corp. of El Segundo, California (hydrazine)
  • Eldec Corp. of Lynnwood, Washington (integrated electronic assemblies)
  • Explosive Technology of Fairfield, California (CDF manifolds)
  • Gaco Western of Seattle, Washington (Hypalon Paint)
  • Lockheed Martin (formerly Martin Marietta) of Denver, Colorado (pyro initiator controllers)
  • Moog Inc. of East Aurora, New York (servoactuators, fuel isolation valves)
  • Motorola of Scottsdale, Arizona (range safety receivers)
  • Pioneer Parachute Company of Manchester, Connecticut (parachutes)
  • Sperry Rand Flight Systems of Phoenix, Arizona (multiplexers / demultiplexers)
  • Teledyne of Lewisburg, Tennessee (location aid transmitters)
  • ATK Launch Systems Corp. of Brigham City, Utah (separation motors)
  • Hamilton Sundstrand of Windsor Locks, Connecticut (auxiliary power units)
  • VACCO Industries of South El Monte, California (safe and arm device)
  • Voss Industries of Cleveland, Ohio (SRB Retention Bands)

Advanced Solid Rocket Motor (ASRM) Project[]

NASA was planning on replacing the post-Challenger SRBs with a new Advanced Solid Rocket Motor (ASRM) to be built by Aerojet[12] at a new facility, designed by subcontractor, RUST International, on the location of a canceled Tennessee Valley Authority nuclear power plant, at Yellow Creek, Mississippi. The ASRM would have produced additional thrust in order to increase shuttle payload, so that it could carry modules and construction components to the ISS. The ASRM program was canceled in 1993 after robotic assembly systems and computers were on-site and approximately 2 billion dollars spent, in favor of continued use, after design flaw corrections, of the SRB.

Filament-wound cases[]

In order to provide the necessary performance to launch polar-orbiting shuttles from the SLC-6 launch pad at Vandenberg Air Force Base in California, SRBs using filament-wound cases (FWC) were designed to be more lightweight than the steel cases used on Kennedy Space Center-launched SRBs.[13] Unlike the regular SRBs, which had the flawed field joint design that led to the Challenger Disaster in 1986, the FWC boosters had the "double tang" joint design (necessary to keep the boosters properly in alignment during the "twang" movement when the SSMEs are ignited prior to liftoff), but used the two O-ring seals. With the closure of SLC-6, the FWC boosters were scrapped by ATK and NASA, but their field joints, albeit modified to incorporate the current three O-ring seals and joint heaters, were later incorporated into the present-day field joints on the current SRBs.

Five-segment booster[]

Prior to the destruction of the Space Shuttle Columbia in 2003, NASA investigated the replacement of the current 4-segment SRBs with either a 5-segment SRB design or replacing them altogether with liquid "flyback" boosters using either Atlas V or Delta IV EELV technologies. The 5-segment SRB, which would have required little change to the current shuttle infrastructure, would have allowed the space shuttle to carry an additional 20,000 lb (Template:Convert/round kg) of payload in an International Space Station-inclination orbit, eliminate the dangerous "Return-to-Launch Site" (RTLS) and "Trans-Oceanic Abort" (TAL) modes, and, by using a so-called "dog-leg maneuver", fly south-to-north polar orbiting flights from Kennedy Space Center. After the destruction of Columbia, NASA shelved the 5-segment SRB for the Shuttle Program, and the three surviving Orbiters, Discovery, Atlantis, and Endeavour were retired in 2011 after the completion of the International Space Station.[14]

A five segment engineering test motor, ETM-03, was fired on October 23, 2003.[15][16]

On September 10, 2009 a five-segment Space Shuttle SRB was static fired on the ground in ATK's desert testing area in Utah. This was the test of what was to be the first stage for the Ares I rocket.[17] Following the cancellation of Ares I with the Constellation Program in 2011, the new Space Launch System was planned to use 5-segment boosters. The first test of the one of the boosters was completed in early 2015. A second test is scheduled to be performed June 28, 2016 at Orbital ATK's Promontory, Utah facility.[18]

Displays[]

Space Shuttle Solid Rocket Boosters are on display at the Kennedy Space Center Visitors Complex in Florida, the Stennis Space Center in Hancock County, Mississippi, United States Space & Rocket Center, Huntsville, Alabama and at Thiokol Missile Systems in Brigham City, Utah.[19]

Future and proposed uses[]

Ares I-X launch 08

The Ares I-X prototype launches from LC-39B, 15:30 UTC, October 28, 2009 – this was as of 2016 the sole flight of a launch vehicle derived from the SRB.

Over time several proposals to reuse the SRB design were presented – however, as of 2016 none of these proposals progressed to regular flights before being cancelled. Until the 2018 planned first flight of the Space Launch System (SLS), a sole test-flight of the Ares I-X prototype in 2009 was the furthest any of these proposals progressed.

Ares[]

NASA planned to reuse the SRB designs and infrastructure in several Ares rockets. In 2005, NASA announced the Shuttle-Derived Launch Vehicle slated to carry the Orion Crew Exploration Vehicle into low-Earth orbit and later to the Moon. The SRB-derived Crew Launch Vehicle (CLV), named Ares I, originally featured a modified standard 4-segment SRB for its first stage, while a liquid-fueled second stage, powered by a single, modified Space Shuttle Main Engine, would have propelled the Orion into orbit.

A later design, introduced in 2006, featured the originally planned, but scrapped 5-segment SRB for its first-stage, with a second stage powered by an uprated J-2X rocket engine derived from the J-2 engine used in the 2nd and 3rd stage of the Saturn V, Saturn IB and Saturn INT-21 rockets. In place of the standard SRB nosecone, the Ares I would have a tapered interstage assembly connecting the booster proper with the second stage, an attitude control system derived from the Regulus missile system, and larger, heavier parachutes to lower the stage into the Atlantic Ocean for recovery.

Also introduced in 2005, was a heavy-lift Cargo Launch Vehicle (CaLV) named Ares V. Early designs of the Ares V utilized five standard-production SSMEs and a pair of 5-segment boosters identical to those proposed for the Shuttle, while later plans redesigned the boosters around the RS-68 rocket engine used on the Delta IV EELV system. Initially, NASA switched over to a system using the 5-segment boosters and a cluster of five RS-68s (which resulted in a widening of the Ares V core unit), then NASA reconfigured the vehicle with six RS-68B engines, with the boosters themselves becoming "5.5-Segment Boosters," with an additional half-segment to provide additional thrust at liftoff.

The current redesign would have made the Ares V booster taller and more powerful than the now-retired Saturn V/INT-20, N-1, and Energia rockets, and would have allowed the Ares V to place both the Earth Departure Stage and Altair spacecraft into Low-Earth orbit for later on-orbit assembly. Unlike the 5-segment SRB for the Ares I, the 5.5-segment boosters for the Ares V were to be identical in design, construction, and function to the current SRBs except for the extra segments. Like the shuttle boosters, the Ares V boosters would fly an almost-identical flight trajectory from launch to splashdown.

The Constellation program, including Ares I and Ares V, was canceled in October 2010 by the passage of the 2010 NASA authorization bill.

DIRECT[]

The DIRECT proposal for a new, Shuttle-Derived Launch Vehicle, unlike the Ares I and Ares V boosters, uses a pair of classic 4-segment SRBs with the SSMEs used on the Shuttle.

Athena III[]

In 2008 PlanetSpace proposed the Athena III launch vehicle for ISS resupply flights under the COTS program – it would have featured 2 1/2 segments from the original SRB design.

Space Launch System (SLS)[]

Saturn V-Shuttle-Ares I-Ares V-Ares IV-SLS Block I&II

Comparison of the Saturn V, Space Shuttle, Ares I, Ares V, Ares IV, SLS Block I and SLS Block II

Main article: Space Launch System

The first versions (Blocks 1 and 1B) of the Space Launch System (SLS) are planned to use two five-segment Solid Rocket Boosters (SRBs), which are based on the four-segment SRBs. Modifications for the SLS included the addition of a center booster segment, new avionics, and new insulation which eliminates the Shuttle SRB's asbestos and is 1,900 lb (Template:Convert/round kg) lighter. The five-segment SRBs provide approximately 25% more total impulse than the Shuttle SRB, and will not be recovered after use.[20][21]

See also[]

  • Solid rocket booster
  • PEPCON disaster

References[]

PD-icon This article incorporates http://www.jsc.nasa.gov/policies.html#Guidelines public domain material from websites or documents of the National Aeronautics and Space Administration.

  1. "NASA – Solid Rocket Boosters". NASA. Archived from the original on 2013-04-06. http://web.archive.org/web/20130406193019/http://www.nasa.gov/returntoflight/system/system_SRB.html. 
  2. Template:Cite book
  3. "One year on – Review notes superb performance of STS-135’s SRBs". http://www.nasaspaceflight.com/2012/07/final-flight-superb-performance-sts-135s-srbs/. Retrieved February 2015. 
  4. "Booster stacking finished for final shuttle flight". http://www.spaceflightnow.com/shuttle/sts135/110418srbs/. Retrieved February 2015. 
  5. "STS-134 IFA Review: SRBs and RSRMs Perform Admirably". http://www.nasaspaceflight.com/2011/06/sts-134-ifa-review-srbs-rsrms-perform-admirably/. Retrieved February 2015. 
  6. "Reusable Solid Rocket Motor—Accomplishments, Lessons, and a Culture of Success". http://ntrs.nasa.gov/archive/nasa/casi.ntrs.nasa.gov/20120001536.pdf. Retrieved February 2015. 
  7. 7.0 7.1 "Shuttle Solid Rocket Boosters". NASA. http://science.ksc.nasa.gov/shuttle/technology/sts-newsref/srb.html. 
  8. "Solid Rocket Boosters". NASA. http://www.nasa.gov/returntoflight/system/system_SRB.html. 
  9. "Solid Rocket Boosters". NASA. Archived from the original on 2010-07-25. http://web.archive.org/web/20100725220547/http://science.ksc.nasa.gov/shuttle/technology/sts-newsref/srb.html. Retrieved 2010-08-28. 
  10. "Salt Water Activated Release for the SRB Main Parachutes (SWAR)". NASA. 2002-04-07. Archived from the original on 2002-02-03. http://web.archive.org/web/20020203162534/http://spaceflight.nasa.gov/shuttle/upgrades/swar.html. 
  11. "Orbiter Manufacturing and Assembly". NASA. http://science.ksc.nasa.gov/shuttle/technology/sts-newsref/sts_asm.html#srb_mods. 
  12. Leary, Warren E., NASA Picks Lockheed and Aerojet, New York Times, April 22, 1989
  13. "Jerry L. Ross" NASA Johnson Space Center Oral History Project, 26 January 2004.
  14. Jenkins, Dennis R. "Space Shuttle: History of the National Space Transportation System – The First 100 Flights"
  15. J. E. McMillin and J. A. Furfaro. "A Review of ETM-03 (A Five Segment Shuttle RSRM Configuration) Ballistic Performance". http://www.csar.illinois.edu/F_viz/gallery/AIAA/RSRMV/McMillinETM-03-AIAA-2004-3895.pdf. 
  16. "Most powerful Space Shuttle Solid Rocket Motor ever tested proves it can be pushed close to edge, yet still perform flawlessly". NASA MSFC. http://www.nasa.gov/centers/marshall/news/news/releases/2003/03-186.html. 
  17. "NASA and ATK Successfully Test Ares First Stage Motor". NASA. Archived from the original on 2010-03-29. http://web.archive.org/web/20100325103340/http://www.nasa.gov/mission_pages/constellation/ares/dm1_success.html. Retrieved 2010-03-25. 
  18. https://www.orbitalatk.com/news-room/release.asp?prid=147
  19. "Launch Vehicles". A Field Guide to American Spacecraft. http://web.mac.com/jimgerard/AFGAS/pages/booster/index.html. 
  20. Priskos, Alex. "Five-segment Solid Rocket Motor Development Status". NASA. http://ntrs.nasa.gov/archive/nasa/casi.ntrs.nasa.gov/20120014501.pdf. Retrieved 2015-03-11. 
  21. "Space Launch System: How to launch NASA’s new monster rocket". NASASpaceFlight.com. 20 February 2012. http://www.nasaspaceflight.com/2012/02/sls-how-to-launch-nasas-new-monster-rocket/. Retrieved 9 April 2012. 

External links[]

Template:Rocket Engines

This page uses Creative Commons Licensed content from Wikipedia (view authors). Smallwikipedialogo.png
Advertisement